93 lines
4.7 KiB
Markdown
93 lines
4.7 KiB
Markdown
# chrony Input Plugin
|
||
|
||
Get standard chrony metrics, requires chronyc executable.
|
||
|
||
Below is the documentation of the various headers returned by `chronyc tracking`.
|
||
|
||
- Reference ID - This is the refid and name (or IP address) if available, of the
|
||
server to which the computer is currently synchronised. If this is 127.127.1.1
|
||
it means the computer is not synchronised to any external source and that you
|
||
have the ‘local’ mode operating (via the local command in chronyc (see section local),
|
||
or the local directive in the ‘/etc/chrony.conf’ file (see section local)).
|
||
- Stratum - The stratum indicates how many hops away from a computer with an attached
|
||
reference clock we are. Such a computer is a stratum-1 computer, so the computer in the
|
||
example is two hops away (i.e. a.b.c is a stratum-2 and is synchronised from a stratum-1).
|
||
- Ref time - This is the time (UTC) at which the last measurement from the reference
|
||
source was processed.
|
||
- System time - In normal operation, chronyd never steps the system clock, because any
|
||
jump in the timescale can have adverse consequences for certain application programs.
|
||
Instead, any error in the system clock is corrected by slightly speeding up or slowing
|
||
down the system clock until the error has been removed, and then returning to the system
|
||
clock’s normal speed. A consequence of this is that there will be a period when the
|
||
system clock (as read by other programs using the gettimeofday() system call, or by the
|
||
date command in the shell) will be different from chronyd's estimate of the current true
|
||
time (which it reports to NTP clients when it is operating in server mode). The value
|
||
reported on this line is the difference due to this effect.
|
||
- Last offset - This is the estimated local offset on the last clock update.
|
||
- RMS offset - This is a long-term average of the offset value.
|
||
- Frequency - The ‘frequency’ is the rate by which the system’s clock would be
|
||
wrong if chronyd was not correcting it. It is expressed in ppm (parts per million).
|
||
For example, a value of 1ppm would mean that when the system’s clock thinks it has
|
||
advanced 1 second, it has actually advanced by 1.000001 seconds relative to true time.
|
||
- Residual freq - This shows the ‘residual frequency’ for the currently selected
|
||
reference source. This reflects any difference between what the measurements from the
|
||
reference source indicate the frequency should be and the frequency currently being used.
|
||
The reason this is not always zero is that a smoothing procedure is applied to the
|
||
frequency. Each time a measurement from the reference source is obtained and a new
|
||
residual frequency computed, the estimated accuracy of this residual is compared with the
|
||
estimated accuracy (see ‘skew’ next) of the existing frequency value. A weighted average
|
||
is computed for the new frequency, with weights depending on these accuracies. If the
|
||
measurements from the reference source follow a consistent trend, the residual will be
|
||
driven to zero over time.
|
||
- Skew - This is the estimated error bound on the frequency.
|
||
- Root delay - This is the total of the network path delays to the stratum-1 computer
|
||
from which the computer is ultimately synchronised. In certain extreme situations, this
|
||
value can be negative. (This can arise in a symmetric peer arrangement where the computers’
|
||
frequencies are not tracking each other and the network delay is very short relative to the
|
||
turn-around time at each computer.)
|
||
- Root dispersion - This is the total dispersion accumulated through all the computers
|
||
back to the stratum-1 computer from which the computer is ultimately synchronised.
|
||
Dispersion is due to system clock resolution, statistical measurement variations etc.
|
||
- Leap status - This is the leap status, which can be Normal, Insert second,
|
||
Delete second or Not synchronised.
|
||
|
||
### Configuration:
|
||
|
||
```toml
|
||
# Get standard chrony metrics, requires chronyc executable.
|
||
[[inputs.chrony]]
|
||
## If true, chronyc tries to perform a DNS lookup for the time server.
|
||
# dns_lookup = false
|
||
```
|
||
|
||
### Measurements & Fields:
|
||
|
||
- chrony
|
||
- last_offset (float, seconds)
|
||
- rms_offset (float, seconds)
|
||
- frequency (float, ppm)
|
||
- residual_freq (float, ppm)
|
||
- skew (float, ppm)
|
||
- root_delay (float, seconds)
|
||
- root_dispersion (float, seconds)
|
||
- update_interval (float, seconds)
|
||
|
||
### Tags:
|
||
|
||
- All measurements have the following tags:
|
||
- reference_id
|
||
- stratum
|
||
- leap_status
|
||
|
||
### Example Output:
|
||
|
||
```
|
||
$ telegraf -config telegraf.conf -input-filter chrony -test
|
||
* Plugin: chrony, Collection 1
|
||
> chrony,leap_status=normal,reference_id=192.168.1.1,stratum=3 frequency=-35.657,last_offset=-0.000013616,residual_freq=-0,rms_offset=0.000027073,root_delay=0.000644,root_dispersion=0.003444,skew=0.001,update_interval=1031.2 1463750789687639161
|
||
```
|
||
|
||
|
||
|
||
|